Are you looking to buy a Matek Dronecan GNSS M10Q-3100 in Australia?
- M10Q-3100 is based on ArudPilots’ AP_Periph firmware, It is a GNSS+COMPASS peripheral with CAN/DroneCAN and UART/MSP interfaces.
- M10Q-3100 uses multi-constellation GNSS powered by u-blox M10 series , It is a concurrent GNSS receiver which can receive and track multiple GNSS systems. Owing to the multi-band RF front-end architecture all four major GNSS constellations, GPS,Galileo, GLONASS and BeiDou can be received concurrently. The high-gain 15 x 15 mm2 patch antenna provides the best balance between performance and small size. The omnidirectional antenna radiation pattern increases flexibility for device installation.
- M10Q-3100 integrates an industrial-grade compass PNI RM3100 which provides high resolution, low power consumption, no hysteresis, large dynamic range, and high sampling rates.
Specifications
- GNSS u-blox M10 series (GPS, GLONASS, Galileo and BeiDou)
- Magnetic Compass PNI RM3100
- Patch GNSS Antenna 15*15*4mm
- CAN Node MCU STM32L431xC
Interface
- CAN(C-H, C-L), DroneCAN Protocol
- UART2((TX2), MSP output
- ST debug, SWCLK & SWDIO
- CAN bootloader LED, Blue
- Fast blinking, Booting
- Slow blinking, working
- GNSS PPS LED, Green
- solid on after powering on
- blinking(1Hz) when GNSS has 3D fixed
- 3.3V LED, Red
- Power supply for M10Q-3100 board : 4.5~5.3V @5V pad/pin
- Power consumption: 50mA
- Operating Temperatures: -20~85 °C
Physical
- Board Size: 36mm*15mm*16mm. 12g
- 3D File M10Q-3100_step.zip
Important information
- on M10-F4-3100, The 3 magnetic coils have little solder paste to avoid the excess to “tilt” them, resulting in some reading inaccuracies of the compass. Any strong impacts will definitely separate them, especially the “tall coil” Sen-Z-f. Pls use this precision module with care.
- Put magnetometer far from power lines/ESC/motors/iron based material. >=10cm
- 2 ears for mounting can be cut off if you don’t need it.
- The default configuration on M10 GNSS module with ublox FW 5.1 is concurrent reception of GPS, Galileo, GLONASS, and BeiDou B1C with QZSS and SBAS enabled.
Start with u-blox GNSS FW3.01, timepulse is aligned with UTC time and that time is set valid only after leap second is downloaded. That could take up to 12.5 min. Probably PPS LED will not blink immediately after GPS has 3D fixed. - The M10Q-3100 provides the ability to reset the receiver. Bridging “Rst” pad(nearby the arrow) to Ground for at least 100 ms will trigger a cold start. RESET will delete all information and trigger a cold start. It should only be used as a recovery option. If you are sure wiring and setup are all right. but GNSS can’t receive any satellites after tens of minutes, try doing reset.
- The scratches on ceramic antenna are the result of tuning the antenna.
Included
- 1x M10Q-3100
- 1x JST-GH-4P to JST-GH-4P 20cm silicon wire
Browse more
Why Choose Phaser FPV?
Here’s Why 1000s of Buyers Trust Us
In the sky-high world of FPV drones and related products, Phaser FPV takes you higher and further – while ensuring a smooth ride every step of the way. As a human brand that puts its clients first, here are a few of the ways we keep giving our customers reasons to come back.
Same-Day Ship
If you place your order with us before 1pm weekdays, we’ll ship it out on the same day you shopped. When we make a promise, we keep it. You’ll be hard-pressed to find any Phaser order that didn’t fly out of our facility on the day it was ordered.
Transparent Stock
We keep our website updated like hawks. If you see it and it says it’s in stock, you can order it today and get it tomorrow via express shipping.
Highly Rated
We’ve spent almost a decade racking in countless 5-star reviews. Give them a read and you'll see everything we have said here is true!
Walk In Anytime
Can’t wait? Then don’t. We’re one of the only FPV drone + accessory stores to have a physical brick-and-mortar establishment in Somersby NSW Australia.
Tech Precision
Our handpicked team of technology experts specialize in – and are boffins on – every product we sell. This means they can answer any and all of your technical questions with confidence. Go ahead, put us to the test.
Fast Support
We welcome our customers to reach out to us via email, phone, or LIVE chat. Phaser FPV is the only FPV business to have a dedicated phone line.
Get Rewarded
Score a FREE gift on first and recurring orders, and discount shipping on orders over $99.
We’re on Social
We have nothing to hide. Follow us on social, tag @PhaserFPV, and become a part of our online community and family in our facebook group.
It’s clear to see why most of our business comes through word-of-mouth referrals. When you need the best in FPV & 3D Printing don’t settle for less. Demand the best – insist on Phaser FPV.
