Sold Out

BetaFPV F4 1-2S AIO Brushless Flight Controller

$65.95

CURRENTLY IN STOCK

Style: SPI FRSKY

  • SPI FRSKY
  • NO RX
$65.95
Add to Wishlist
SKU: 9455N/A W/H: N/A Barcode: N/A Shipping Weight: 50g N/A Categories: Beta65 pro , Beta75 Pro , BetaFPV , BetaFPV Beta65X 2020 , BetaFPV Beta65x HD 2020 , BetaFPV FC , Drone ESCs , Tiny Whoop Tags: BetaFPV, Flight Controller

We accept the following payment methods

This AIO F4 FC is suitable for a lighter 1-2S whoop drone perfectly, like Beta65 Pro 2or Beta75 Pro 2 etc. It integrated with a Betaflight F411 processor FC, Betaflight OSD, SPI Frsky receiver and 1-2S 5A ESC. So the 1-2S drone could save much weight for a faster fly experience.

F4 2S AIO Brushless Flight Controller

This FC is available for 1S whoop drone also. You need to solder JST-PH 2.0 Cable in wires solder pad to replace the initial power cable. At the same time, you need to use higher than 12000KV motors, such as 0802 17500KV / 19500KV Motors to provide more power.

    SPECIFICATIONS OF FC

    • CPU: STM32F411CEU6 (100MHZ )
    • Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
    • Size: 26mm x 26mm, fully compatible with the all whoop drone mounting pattern, recommend the Beta65X frame and Beta75 Pro frame.
    • Firmware version: betaflight_matekf411rx_4.0.0 (Development Version)
    • OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
    • Built in SPI Frsky D16 protocol native receiver, compatible with almost ALL Frsky FCC radios(e.g. Taranis X9D/X9D Plus/X7) or Frsky compatible transmitter module. Not compatible with Frsky LBT protocol.
    • Power Cable: 55mm, with 2pcs JST-PH 2.0 connector, AKA PowerWhoop connector
    • Weight: 4.5g 

    DIAGRAM FOR F4 2S AIO FC (FRSKY/FUTABA RX)

    Updated: For easier self-assembly, we added another set of 5V&GND solder pad on Frsky/Futaba FC.

      SPECIFICATIONS OF ESC

      • Built-in ESC with 5A continuous and peak 6A current
      • Power supply: 1-2S
      • Support BLHeliSuite programmable
      • Factory firmware: S_H_50_REV16_7.HEX
      • Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM

      Status LED

      There are 3 LEDs on the bottom of the board to indicate the status, including Receiver LED ( Green), FC Status LED ( Red ) and FC Power LED ( Blue ). 

      LED

      Status

      Description

      Receiver LED ( Green)

      Solid

      Connected or in bind mode

      Receiver LED ( Green)

      Flashing

      Not connected

      Power LED ( Blue )

      Solid

      Power on

      Status LED ( Red )

      Solid

      Motor Armed

      SPI Frsky Receiver

      Currently the built in Frsky receiver is compatible with Taranis, Taranis Plus, X9E, Horus X12S, XJT Modules. Pay attention, this is a SPI connection receiver. In Betaflight Configuration, it should be setted as FRSKY_D receiver (aka Frsky D8 mode) or FRSKY_X receiver (aka Frsky D16 mode) in SPI RX mode.

       

      The Frsky D16 unstable connection issue is totally resolved since Betaflight 3.4.1. Nowadays, the default configuration from factory is Frsky D16 mode (FRSKY_X).

      Note: If you are using EU-LBT firmware radio controller, you might find that you can't bind successfully to this SPI Frsky receiver. Here are the solutions we provide for you. Thanks to Sebastian Abramowski for giving us the important feedback about binding to EU-LBT firmware radio controller. 

      Binding Procedure

      The binding procedure is reversed as usual. No need to click the bind button when power on.

      • Power on the board, either by connecting the battery or USB power. Then the green receiver LED start to flash.
      • The second step, click the bind button for 3s. Then the green receiver LED will be solid on. This means that the receiver is in bind mode and you could start to bind your radio transmitter.

      For detail procedure of binding, please check the SPI Frsky Receiver Binding Manual.

      Note: This FC board could support the SPI Futaba protocol with this firmware.

      Some pilots would complaint that it is definitely not a long range FC. It looses signal with my transmitter far too often and for what appears to be no reason. This issue is often caused by the location of the antenna. You should keep the antenna away from the FC board to get a stronger signal. For example, run the singal upwards. Thanks for Harley Finberg's advice.

      CLI DUMP of F4 2S Brushless FC

      You can get the Cli dump of F4 AIO 2S Brushless FC here on the BETAFPV Support Freshdesk.

      DIAGRAM FOR F4 2S AIO FC (NO RX)

       

      HOW TO CONNECT THE EXTERNAL RX TO THE FC

      For detailed information of other external receivers, please find out in our support page.

      FAQ

      1. Can this FC used on the Beta75X with 1103 motors?

      Yes, we have tested this FC board with 1103 motors on Beta75X. It performance very well and almost no wash-out issue then. So if you already have a Beta75X, you could just take this AIO FC to replace the stock FC&ESC stack.

      Note: because of the built-in ESC and Frsky receiver, you will lose some remote range and little bit power on Beta75X with this AIO FC.

      2. About the alarm buzzer and LED port?

      No alarm buzzer is supported on this FC board. Programable LED is supported.

        RECOMMENDED PARTS LIST

        PACKAGE

        • 1 * F4 2S brushless flight controller
        • 4 * M1.2x4mm screws
        • 4 * M1.4x5mm screws
        • 4 * Anti-vibration ruber dampers

        Why Choose Phaser FPV?

        Here’s Why 1000s of Buyers Trust Us

        In the sky-high world of FPV drones and related products, Phaser FPV takes you higher and further – while ensuring a smooth ride every step of the way. As a human brand that puts its clients first, here are a few of the ways we keep giving our customers reasons to come back.

        Same-Day Ship

        If you place your order with us before 1pm weekdays, we’ll ship it out on the same day you shopped. When we make a promise, we keep it. You’ll be hard-pressed to find any Phaser order that didn’t fly out of our facility on the day it was ordered.


        Transparent Stock

        We keep our website updated like hawks. If you see it and it says it’s in stock, you can order it today and get it tomorrow via express shipping.

        Highly Rated

        We’ve spent almost a decade racking in countless 5-star reviews. Give them a read and you'll see everything we have said here is true!

        Walk In Anytime

        Can’t wait? Then don’t. We’re one of the only FPV drone + accessory stores to have a physical brick-and-mortar establishment in Somersby NSW Australia.

        Fast Support

        We welcome our customers to reach out to us via email, phone, or LIVE chat. Phaser FPV is the only FPV business to have a dedicated phone line.

        We’re on Social

        We have nothing to hide. Follow us on social, tag @PhaserFPV, and become a part of our online community and family in our facebook group.

        It’s clear to see why most of our business comes through word-of-mouth referrals. When you need the best in FPV & 3D Printing don’t settle for less. Demand the best – insist on Phaser FPV.

        Sunday,Monday,Tuesday,Wednesday,Thursday,Friday,Saturday
        January,February,March,April,May,June,July,August,September,October,November,December
        Not enough items available. Only [max] left.
        Shopping cart

        Your cart is empty.

        Return To Shop

        Add Order Note Edit Order Note
        Estimate Shipping
        Add A Coupon

        Estimate Shipping

        Add A Coupon

        Coupon code will work on checkout page